What the Editors-in-Chief say about the review process in our Journals: Our Editors-in-Chief declare, confirm, certify and sign the substantial, important, line by line peer review process and our high-rejection rates.
Published Articles with Keyword: machining
- Title: Aspects Regarding Knowledge-based Engineering
Authors: Daniela Ghelase, Luiza Daschievici
Doi: 10.37394/23205.2023.22.6
Download | Download
Published in WSEAS Transactions on Computers, Volume 22, 2023 - Title: Contributions to the Experimental Study Regarding the Influence of the Cutting Fluid on the Grinding Process Performances
Authors: Constantin Buzatu, Adela-Eliza Dumitrascu
Doi: 10.37394/232024.2022.2.1
Download | Download
Published in Earth Sciences and Human Constructions, Volume 2, 2022 - Title: Research Regarding the Improving of the Machining Parameters in the Field of Grinding Process
Authors: Badea Lepadatescu
Doi: 10.37394/232012.2020.15.14
Download | Download
Published in WSEAS Transactions on Heat and Mass Transfer, Volume 15, 2020 - Title: Architecture and Simulation for Knowledge Management in Engineering
Authors: Daniela Ghelase, Luiza Daschievici
Doi: 10.37394/23205.2020.19.8
Download | Download
Published in WSEAS Transactions on Computers, Volume 19, 2020 - Title: Numerical Modeling the Effects of Chamfer and Hone Cutting Edge Geometries on Burr Formation
Authors: Muhammad Asad, Faramarz Djavanroodi, Hassan Ijaz, Muhammad Azhar Ali Khan, Muhammad Usman Rashid, Tarek Mabrouki
Doi: 10.37394/232011.2020.15.17
Download | Download
Published in WSEAS Transactions on Applied and Theoretical Mechanics, Volume 15, 2020 - Title: Investigation the Effects of Cutting Parameters on Geometric Accuracy of Machining Marine Propeller using 3D Photo-scanning Technique
Authors: Mahfudz Al Huda, Khairul Jauhari, Erwien Yuliansyah, Achmad Zaki Rahman, Endarto Tri Wibowo
Doi: 10.37394/232011.2020.15.1
Download | Download
Published in WSEAS Transactions on Applied and Theoretical Mechanics, Volume 15, 2020 - Title: MRR-Based Productivity Decisions in Hard Machining
Authors: Janos Kundrak, Viktor Molnar, Istvan Deszpoth
Download | Download
Published in WSEAS Transactions on Environment and Development, Volume 14, 2018 - Title: Correlation Between Chip Ratio and Specific Forces with Increasing Feed per Tooth and Cutting Speed in Face Milling of Steel
Authors: János Kundrák, Angelos P. Markopoulos, Tamás Makkai, Antal Nagy
Download | Download
Published in WSEAS Transactions on Environment and Development, Volume 14, 2018 - Title: Investigation into Application of Electrical Discharge Machining as a Surface Treatment Process
Authors: Meena Laad, Vijaykumar S. Jatti, Pratik Prakash Jadhav
Download | Download
Published in WSEAS Transactions on Applied and Theoretical Mechanics, Volume 9, 2014 - Title: Generation of Machined Multiple Flat Surfaces on Circular Bar by its Rotation and in Synchronism with Cutting Tool
Authors: J. A. Martins, C. Schuermann, D. Leite, I. Kövesdy, E. A. Duarte, E. Romão
Download | Download
Published in WSEAS Transactions on Applied and Theoretical Mechanics, Volume 8, 2013 - Title: Study of Workpiece Thermal Profile in Electrical Discharge Machining (EDM) Process
Authors: Ali Moarrefzadeh
Download | Download
Published in WSEAS Transactions on Applied and Theoretical Mechanics, Volume 7, 2012